series pms, ppr, ppt resistors & terminations high power, thin film, drop-in C 10-650 watts, dc-4 ghz notes 1. input power ratings are based on flange temperature of 100 c maximum. 2. 50 and 100 ohms standard. other values from 10-500 ohms available on special order. contact factory for details. standard tolerance 5%. specify resistance value when ordering. 3. vswr applies to termination style only. general speci fications resistive element thin film and thick film* substrate beryllium oxide ceramic cover alumina ceramic mounting flange copper,nickel plated per qq-n-290 tab beryllium copper,gold plated per mil-g-45204 average power derating curv e flange temperature ? c power derating % of rated power 100 100 125 150 75 75 50 50 25 25 0 frequency input power vswr (typical) capacitance figure model range (watts avg.) (note 3) (pf) (typ.) no. ppr & ppt 300-10-3* dc-4.0 ghz 10 1.35:1 ?dc-4.0 ghz 0.8 1 pms-100 & pms-200* dc-2.0 ghz 20 1.25:1 ?dc-2.0 ghz 1.2 2 ppr & ppt 515-20-3* dc-2.0 ghz 20 1.10:1 ?dc-1.0 ghz 0.8 3 1.25:1 ?1.0-2.0 ghz ppt515-30-4 dc-4.0 ghz 30 1.20:1 ?dc-4 ghz 1.2 4 ppr & ppt 515-30* dc-2.0 ghz 30 1.10:1 ?dc-1.0 ghz 0.8 5 1.25:1 ?1.0-2.0 ghz ppr & ppt 800-40-3 dc-4.0 ghz 40 1.25:1 ?dc-4.0 ghz 1.4 6 ppt800-100a dc-2.0 ghz 100 1.25:1 ?dc-2.0 ghz 1.4 7 ppr & ppt 870-150-3* dc-1.0 ghz 150 1.20:1 ?dc-500 mhz 3.5 8 1.35:1 ?500-1000 mhz ppr & ppt 975-250-3 dc-1.0 ghz 250 1.25:1 ?dc-500 mhz 5.0 9 1.35:1 ?500-1000 mhz ppr & ppt 1250-400 dc-500 mhz 400 1.50:1 ?dc-500 mhz 7.0 10 ppr &ppt 1900-800 dc-500 mhz 650 1.25:1 ?dc-200 mhz 10.2 11 1.50:1 ?200-500 mhz performance specifications general information these high power devices are designed to dissipate power in r.f. circuits when mounted to an appropriate heat sink. the ter- minations provide a low vswr under maximum power condi- tions. the resistor configurations are typically used in wilkinson type power divider networks, or to terminate 3 db stripline or microstrip hybrids. * low cost thick film models available on some sizes.consult factory for specifications. terminations (ppt) series resistors (ppr) series figures ppt 300-10-3 ? 10 watts flange mounted ppr 300-10-3 ? 10 watts flange mounted fig. 1 pms 100 ? 20 watts stud mounted pms 200 ? 20 watts stud mounted fig. 2 .062 [1.57] .100 [2.54] .100 [2.54] .200 [5.08] .300 [7.62] .200 [5.08] .005 .001 [0.13 0.03] .110 [2.79] .030 [0.76] .040 [1.02] .125 [3.17] min .160 [4.06] max .116 [ 2.95] .060[1.52] max. .250[6.4] .250 [6.4] .065[1.65] typ. .092[2.34] typ. .062 [1.57] .375[9.53] .032[0.81] wide x .035[0.89] deep slot 6-32 nc-2a thd .500 .015 [12.7 0.38] typ. .003 .001 [0.08 0.03] physical dimensions terminations (ppt) series resistors (ppr) series figures rev 7/06 key : inches [millimeters] .xx .03 .xxx .010 [.x 0.8 .xx 0.25] rohs
fig. 3 ppt 515-20-3 ? 20 watts flange mounted ppr 515-20-3 ? 20 watts flange mounted fig. 5 ppt 515-30 ? 30 watts flange mounted ppr 515-30 ? 30 watts flange mounted fig. 4 ppt 515-30-4 ? 30 watts flange mounted offered as a termination only! .005 .001 [0.13 0.03] tab thickness .040 [1.02] .560 [14.22] .800 [20.32] .108 [2.74] .060 [1.52] .150 [3.81] max .150 [3.81] min .400 [10.16] .120 [3.05] .115 [2.92] .230 [5.84] .130 [3.30] thru 2 pls ppt 800-40-3 ? 40 watts flange mounted ppr 800-40-3 ? 40 watts flange mounted fig. 6 terminations (ppt) series resistors (ppr) series figures physical dimensions terminations (ppt) series resistors (ppr) series figures .003 .001 [0.08 0.03] .130 [3.30] .062 [1.57] .160 [4.06] max .250 [6.35] .125 [3.18] .125 [3.18] .060 [1.52] typ .095 [2.41] .250 [6.35] min .515 (13.08) .250 [6.35] min .116 [2.95] .003 .001 [0.08 0.03] .130 [3.30] .062 [1.57] .160 [4.06] max .250 [6.35] .125 [3.18] .125 [3.18] .060 [1.52] typ .095 [2.41] .250 [6.35] min .515 (13.08) .250 [6.35] min .116 [2.95] .003 .001 [0.08 0.03] .110 [2.79] .062 [1.57] .150 [3.81] max .250 [6.35] .125 [3.18] .125 [3.18] .060 [1.52] typ .095 [2.41] .250 [6.35] min .515 (13.08) .250 [6.35] min .116 [2.95] series pms, ppr, ppt resistors & terminations key : inches [millimeters] .xx .03 .xxx .010 [.x 0.8 .xx 0.25]
.003 .001 [0.08 0.03] .062 [1.57] .155 [3.94] .160 [4.06] max .187 [4.76] .375 [9.52] .120 [3.05] .250 [6.35] .560 [14.22] .870 [22.10] .125 [3.18] min .108 [2.74] .161 [4.09] thru 2 pls terminations (ppt) series resistors (ppr) series figures physical dimensions terminations (ppt) series resistors (ppr) series figures fig. 8 fig. 9 ppt 870-150-3 ? 150 watts flange mounted ppr 870-150-3 ? 150 watts flange mounted ppt 975-250-3 ? 250 watts flange mounted ppr 975-250-3 ? 250 watts flange mounted ppt 1250-400 ? 400 watts flange mounted ppr 1250-400 ? 400 watts flange mounted fig. 10 .005 .001 [0.13 0.03] tab thickness .040 [1.02] .560 [14.22] .800 [20.32] .108 [2.74] .060 [1.52] .150 [3.81] max .150 [3.81] min .400 [10.16] .120 [3.05] .115 [2.92] .230 [5.84] .130 [3.30] thru 2 pls fig. 7 offered as a termination only! ppt 800-100a ? 100 watts flange mounted .200 [5.08] max .375 [9.53] .110 [2.79] .300 [7.62] .125 [3.18] min .975 [24.77] .375 [9.52] .725 [18.41] .120 [3.05] .125 [3.17] .171 [4.34] .125 [3.17] thru 2 pls .188 [4.76] .003 .001 [0.08 0.03] .500 [12.7] 1.250[31.8] .125 [3.18] min. 500[12.7] .250[6.4] .875 [22.23] .120[3.05] typ. .160[4.06] dia typ. .125[3.18] .210[5.33] max. .171[4.34] .003 .001 [0.08 0.03] series pms, ppr, ppt resistors & terminations key : inches [millimeters] .xx .03 .xxx .010 [.x 0.8 .xx 0.25]
fig. 11 ppt 1900-800 ? 650 watts flange mounted ppr 1900-800 ? 650 watts flange mounted .125 [3.18] min .250 [6.35] 1.550 [39.37] 1.000 [25.40] 1.900 [48.26] 1.040 [26.42] .175 [4.45] .500 [12.70] .270 [6.86] l c .195 [4.95] .125 [3.18] .166 [4.22] thru 4 pls .005 .001 [0.13 0.03] .250 [6.35] max terminations (ppt) series resistors (ppr) series figures physical dimensions terminations (ppt) series resistors (ppr) series figures series pms, ppr, ppt resistors & terminations key : inches [millimeters] .xx .03 .xxx .010 [.x 0.8 .xx 0.25] k di-resistor produc ts 60 south jefferson road, whippany, nj 07981 tel: 973-887-8100 ? fax: 973-884-0445 www.aeroflex-kdi.com ? sales@aeroflex-kdi.com key : inches [millimeters] .xx .03 .xxx .010 [.x 0.8 .xx 0.25]
|
